moxa_banner
FRM220 In-band Managed Multi-service Platform
FRM220-1000DS
FRM220-1000DS

  • 1000Base-T to 1000Base-SX/LX
  • Network management via terminal or SNMP in FRM220 chassis
  • Auto-negotiation or force mode
  • Auto MDI/MDIX
  • Forward > 9K bytes packets
  • Support Link Fault Pass Through (LFP) function
  • Auto Laser Shutdown (ALS)

FRM220-DS3/E3
FRM220-DS3/E3

  • In-band network Managed via Terminal, web or SNMP in FRM220 chassis
  • DS3/E3 Coax (BNC) to Fiber SFP fiber modem
  • Supports AIS (Alarm Indication Signal)
  • User selectable E3 or DS3 setting
  • Electrical and optical Loop back tests
  • Standalone RS232 console management via CH01M

FRM220-1000EAS/X-1
FRM220-1000EAS/X-1

  • 10/100/1000Base-T to 1000Base-X SFP
  • Supports local / remote IEEE802.3ah OAM / IP In-band management
  • Stand-alone IP Based, Web GUI, Telnet, SNMP management
  • Auto-Negotiation or forced mode
  • Auto MDI/MDIX
  • Forward 10K bytes Jumbo packets (max.)
  • Supports Q in Q double tagging
  • Supports IEEE 802.1Q Tagging
  • Supports Flow control (Pause)
  • Supports OAM remote loopback to assist in diagnosing network problems
  • Supports bandwidth control
  • Supports remote CPE power fail detect (dying gasp)
  • Supports Far End Fault Indication (FEFI)
  • Supports Link Fault Pass-Through (LFPT)
  • Supports RMON counter
  • D/D function for supported SFP fiber transceiver
  • Auto Laser Shutdown (ALS)
  • Online local / remote f/w upgrade
  • Default port and IEEE802.1Q Tagging priority QoS

FRM220A-FSW103
FRM220A-FSW103

  • 3 Port 10/100BASE-TX + 1 Port 100BASE-FX Ethernet Switch
  • Auto-Cross over for MDI/MDIX in TP port
  • Auto-Negotiation or Manual mode in TP port
  • Support flow control
  • Forward 1552 bytes (max.) packets in switch mode
  • Support Store and forward switch mode
  • Support FRM220 chassis management system
  • Support FRM220A chassis management System and Ethernet Aggregation
  • Support the local management (Monitor or Configure status) by the SNMP manager.
  • Support D/D function for SFP fiber transceiver
  • Provide Auto Laser Shutdown (ALS) function
  • Provide Product information for management
  • Support On-Line F/W upgrade (local) by the SNMP manager

FRM220-1000MS
Gigabit Ethernet OAM/IP In-band Media Converter


The FRM220-1000MS is an IEEE802.3ah OAM compliant copper to fiber Gigabit Ethernet solution designed to make conversion between 10/100/1000Base-TX and dual rate 100/1000Base-X with SFP LC connector. When deployed as a stand-alone solution, this media converter incorporates an easy to use Web user interface for operation, administration and maintenance of both local and remotely connected FRM220-1000MS converters. By offering 802.3ah OAM compliance, this converter can be linked to any 802.3ah compliant fiber switch and support loop back and dying gasp functions. When placed in our centrally controlled and managed rack, all functions of this converter and the remotely connected converter can be configured and monitored via in-band management, including band-width control, duplex, speed, VLAN configuration and more.

FRM220-CH08
FRM220-CH08

  • 1U 19" 8-slot Chassis with AC/DC power redundancy
  • All modules and cards support hot-swapping
  • Chassis backplane consists of passive components
  • Two alarm relays

FRM220A-1002ES
FRM220A-1002ES

  • 2 Port 10/100/1000BASE-T to 2 Port 100/ 1000BASE-X Converter
  • Auto-Cross over for MDI/MDIX in TP port
  • Auto-Negotiation or Manual mode in TP port
  • Supports flow control Enable or Disable
  • Supports Jumbo Frame 10K Bytes
  • Supports 16 Tag VLAN Group
  • Supports Double VLAN tag (Q-in-Q)
  • Supports Bandwidth control
  • Supports Loop Back Test
  • Supports Link Fault Pass Through ( LFP ) Function
  • Supports Auto Laser Shutdown (ALS) Function
  • Supports local management on FRM220A rack management.
  • Console management on stand-alone.
  • Supports D/D function for SFP fiber transceiver
  • Provide Product information for management
  • Supports the local management (Monitor or Configure status) by the SNMP manager.
  • Supports FRM220A for Ethernet Aggregation

FRM220-4G-2S
4G Multi-Protocol Transponder / Repeater
FRM220-4G-2S

The FRM220‐4G‐2S is a 2R 4Gbps optical regeneration device, which consists of Re‐amplification and Re‐shaping. The transponder card converts a data signal to the correct wavelength for transmission on a specific channel by supporting SFP optics on both line side and client side interfaces. When the FRM220‐4G‐2S card is placed in the FRM220 rack with SNMP management, the management can view the converter card's status, type, version, fiber link status and alarms. The card can be configured to enable or disable the port, reset the port and perform diagnostic loop backs.

FRM220-100M
Fast Ethernet OAM/IP In-band Media Converter
FRM220-100M

The FRM220-100M is an IEEE802.3ah OAM compliant copper to fiber Fast Ethernet solution designed to make conversion between 10/100Base-TX and 100Base-FX with SC, FC ,ST connector. When deployed as a stand-alone solution, this media converter incorporates an easy to use Web user interface for operation, administration and maintenance of both local and remotely connected FRM220-100M converters. By offering 802.3ah OAM compliance, this converter can be linked to any 802.3ah compliant fiber switch and support loop back and dying gasp functions. When placed in our centrally controlled and managed rack, all functions of this converter and the remotely connected converter can be configured and monitored via in-band management, including band-width control, duplex, speed, VLAN configuration and more.

FRM220-4G-3S
4G Multi-Protocol Transponder / Repeater
FRM220-4G-3S

The FRM220‐4G‐3S is a 2R 4G optical regeneration device, which consists of Re‐amplification and Re‐shaping. The transponder card converts a data signal to the correct wavelength for transmission on a specific channel by supporting SFP optics on both line side and client side interfaces. 1+1 Automatic optical line Protection Switching is supported for the aggregate fiber ports. When the FRM220‐4G‐3S card is placed in the FRM220 rack with SNMP management, the management can view the converter card's status, type, version, fiber link status and alarms. The card can be configured to enable or disable the port, reset the port and perform diagnostic loop backs.

FRM220-NMC
Network Management Controller
FRM220-NMC

The FRM220-NMC is a Network Management Controller card that can be placed in a compatible FRM220 series chassis to provide network management functions. The management interface supports a local RS-232 serial console or remote TCP/IP management by Telnet, HTTP or SNMP protocols. The card is designed to be hot swapped so that it may be field replaced without affecting any online service of any other rack cards. The card also supports online firmware upgrade from TFTP server, using any user interface.Support for any standard NMS is provided by the included enterprise MIB file.

FRM220
FRM220

The FRM220 is a 2U high 19" Rack, 20 slot modular media converter rack. Technologies Supported: > 10G, 2.7G 3R Transponder > Gigabit Ethernet Converter > Fast Ethernet Converter > Fiber Multiplexer > POTS Fiber Converter > Fiber Repeater > E1/T1 Fiber Modem > V35/X21/RS530 Fiber Modem > Serial RS485/422 Fiber Converter

FRM220-10/100i-2E
Fast Ethernet In-band Media Converter
FRM220-10_100i-2E

The FRM220-10/100i-2E is a 2-port 10/100Base Ethernet to 100Base-FX fiber slide-in card converter designed for central and remote applications. With advanced features like bandwidth control, this media converter is targeted for customer premises equipment in metro LAN, campus, enterprise and FTTx applications. By offering in-band management, this converter can be completely controlled and monitored from a centrally located managed standalone chassis controlling all converter settings including band-width control, duplex, and speed configuration. This media converter is completely transparent to Layer 2 and Layer 3 protocols including IEEE 802.1q, VLAN tag, Q in Q, STP, IPX, IP, etc.

FRM220-10G-SXX
10G 3R Transponder
FRM220-10G-SXX

The FRM220-10G-SXX is a manageable 10G fiber to fiber 3R repeater and transponder. Based on a number of 10 Gigabit Fiber standards, this transponder supports XFP to XFP, SFP+ to XFP, or SFP+ to 1+1 fiber protection over dual XFP fiber connections.

FRM220-10G-SS
10G 3R Transponder
FRM220-10G-SS

The FRM220-10G-SS is a manageable 10G fiber to fiber 3R repeater and transponder. Based on a number of 10 Gigabit Fiber standards, this transponder supports SFP+ to SFP+ (SS) fiber connections.

FRM220-FOM01
FRM220-FOM01

  • 1 channel unframed E1/T1
  • 10/100Base-TX Ethernet (100M wirespeed)
  • Auto MDI/MDIX
  • Auto-Negotiation or Force mode
  • Supports flow control
  • Supports 9K jumbo packets
  • Supports Link fault pass through for Ethernet
  • Supports Digital Diagnostics Monitoring Interface (DDMI) SFP
  • Loopback test on E1/T1, fiber ports
  • Supports Dying Gasp
  • Supports local or remote In-band management by SNMP manager
  • Local management by console port via FRM220-CH01M chassis.
  • Supports On-Line F/W upgrade.

FRM220-2.7G-2S
2.7G 3R Transponder

The FRM220-2.7G-2S is a 2.7G 3R optical regeneration device, which consists of Re-amplification, Re-shaping and Re-timing. The transponder card converts a data signal to the correct wavelength for transmission on a specific channel by supporting SFP optics on both line side and client side interfaces.

FRM220-2.7G-3S
2.7G 3R Transponder with Fiber Protection

The FRM220-2.7G-3S is a 3R 2.7G optical regeneration device, which consists of Re-amplification, Re-shaping and Re-timing. The transponder card converts a data signal to the correct wavelength for transmission on a specific channel by supporting SFP optics on both line side and client side interfaces. 1+1 Automatic optical line Protection Switching are supported for the aggregate fiber ports.

FRM220-MD40 WA/WB
FRM220-MD40 WA/WB

  • Full native mode performance
  • Optical connectors
  • Passive model requires no power
  • Protocol transparent, no limitation
  • Utilizes industry standard ITU CWDM wavelength

FRM220A-1000EAS/X
FRM220A-1000EAS/X

The FRM220A-1000EAS/X is an IEEE802.3ah OAM compliant dual copper to dual fiber Gigabit Ethernet solution designed to make conversion between 10/100/1000Base-TX and 1000Base-SX/LX with SFP connector.

FRM220-1000EAS
Gigabit Ethernet OAM/IP In-band Converter/ Switch

The FRM220-1000EAS is an IEEE802.3ah OAM compliant dual copper to dual fiber Gigabit Ethernet solution designed to make conversion between 10/100/1000Base-TX and 1000Base-SX/LX with SFP connector. With SNMP and Web-based management in the FRM220, the network administrator can monitor, configure and control the activity of each 802.3ah series card and remotely connected OAM compliant converter.

FRM220-1000EAS-1
FRM220-1000EAS-1

The FRM220-1000EAS-1 is an IEEE802.3ah OAM compliant copper to fiber Gigabit Ethernet solution designed to make conversion between 10/100/1000Base-TX and 1000Base-SX/LX with SFP connector.

FRM220-1000ES
FRM220-1000ES

The FRM220-1000ES is a copper to fiber Gigabit Ethernet solution designed to make conversion between 10/100/1000Base-TX and 1000Base-SX/LX with SC or SFP LC connector. With SNMP and Web-based management in the FRM220, the Network administrator can monitor, configure and control the activity of each card in the chassis.

FRM220-1000TS
Managed Gigabit Ethernet Converter

The FRM220-1000TS is a transparent Gigabit Ethernet 1000Base-T to 1000Base-SX/LX SFP converter. They are managed (when installed in FRM220 with NMC) or non-managed stand-alone media converters, which give you the options to choose from a wide range of industry standard SFP modules with LC connectors.

FRM220-10/100A
Fast Ethernet OAM/IP In-band Media Converter

The FRM220-10/100A is an IEEE802.3ah OAM compliant copper to fiber Fast Ethernet solution designed to make conversion between 10/100Base-TX and 100Base-FX with SC, FC or ST connector.

FRM220-10/100AS-2
Dual Channel Fast Ethernet OAM/IP In-band Media Converter

The FRM220-10/100AS-2 is an IEEE802.3ah OAM compliant two copper to two fiber Fast Ethernet solution designed to make conversion between 10/100Base-TX and 100Base-FX with SFP.

FRM220-10/100i
FRM220-10/100i

  • 10/100Base-TX to 100Base-FX Converter
  • Auto-Negotiation or forced mode
  • Supports remote CPE power fail detect (dying gasp)
  • Supports Far End Fault
  • Supports Link Fault Pass through (LFP)
  • Supports Loop Back Test
  • Supports RMON counter
  • D/D function for supported SFP fiber transceiver
  • Auto Laser Shutdown (ALS)
  • Auto MDI/MDIX
  • Forward 2046 bytes (max.) packets in switch mode
  • Forward 9K jumbo packets in converter mode
  • Supports Q in Q double tagged frame transparent
  • Supports IEEE 802.1q Tag VLAN pass thru
  • Supports local / remote In-band management (Monitor and Configure) by the SNMP manager.
  • Bandwidth control (Nx32K or Nx512Kbps)
  • Support flow control (Pause)
  • Fiber Hardware Reset (FHR)
  • Online local / remote f/w upgrade
  • Must be placed in managed chassis to realize any management features

FRM220-10/100iS-2
Dual Channel Fast Ethernet In-band Media Converter

The FRM220-10/100iS-2 is a dual channel (two in one)10/100Base Ethernet to 100Base-FX fiber slide-in card converter designed for central and remote applications. With advanced features like bandwidth control, this media converter is targeted for customer premises equipment in metro LAN, campus, enterprise and FTTx applications.

FRM220-FXO/FXS
FXO/FXS 2-wire POTS Fiber Converter

FRM220-FXO/FXS POTS phone line converter extender is used to connect PSTN voice signals to distant Plain Old Telephone (POTS) devices. FRM220-FXO/FXS provides a fiber media transport for POTS transmission and features an RJ-11C for copper connection. A pair of FRM220-FXO/FXS is required to implement an end to end system.

FRM220-E1/T1
E1/T1 Fiber modem

The FRM220-E1/T1 is a fiber media transport for G.703 E1/T1 transmissions. The BNC model provides unbalanced 75 Ohm coaxial E1 connections while the RJ-45 model provides switchable balanced 120 Ohm E1 or 100 Ohm T1 connections over twisted pair wiring.

FRM220-E1/Data
FRM220-E1/Data

The FRM220-E1/DATA slide in card DSU/CSU is a digital access unit for Unframed or Fractional E1 services. The FRM220-E1/DATA data channel supports user-selectable transmission rates via randomly selected E1 timeslots, which provides integral multiples of 64kbps or 56kbps, up to a maximum 2.048Mbps (unframed), for a line attenuation of up to 43 dB on twisted pair or coax cable. This provides an approximate operating range up to 2km (using 22AWG). The FRM220A-E1/DATA front panel provides status LEDs for monitoring the CSU and DSU conditions for initiating local and remote loopback with integral BERT.

FRM220-Serial
RS485/422/232 Fiber modem

The FRM220-Serial provides a fiber converter solution to extend asynchronous RS-485 or RS-232 transmission distance up to 2km over multimode fiber or up to 120km over single mode fiber. The converter is equipped with multiple interface circuits for connection to RS-232 or RS-485/422 (2 or 4 wire, full or half duplex).

FRM220-FOM04
4-port E1/T1+100M Ethernet Fiber Multiplexer

FRM220-FOM04 is a modular design for 4xT1 + Fast Ethernet multi-service to dual strand fiber PDH multiplexer.FRM220-FOM04 provides T1 transmission transparently, pure 100Mbps Fast Ethernet simultaneously. The fiber optic line is based on the SFP technology that allows a flexible use of Multimode or Single mode lines and enable the support of different wavelengths and distances.

FRM220-FTEC
FRM220-FTEC

  • Converts between T1 and E1 data and signaling
  • Enable equipment to operate at T1 and E1 rates
  • Support G.802 Annex B (T1 over E1)
  • Configures A-law/μ-law and signaling conversion
  • Transparent conversion at 64kbps timeslot level
  • Controlled slip for buffer over or under flow
  • 24 timeslots of T1 Nx64 can be inserted into E1 Nx64, 30/CAS or 31/CCS timeslots

FRM220-E1/Data
FRM220A-E1 DATA

  • Supports Fractional E1 and Unframed E1 services with V.35/X21/RS530 adapter cable
  • I/O connectors all located on front panel
  • Multiple clock source selection and remote loopback ( Internal or External: E1 recovery, DTE or DCE )
  • Unbalanced E1/BNC or balanced E1/RJ45
  • Fully compatible with FRM220-CH20 and FRM220A chassis
  • SNMP management with FRM220-CH20 chassis
  • LED Alarm indication
  • Standalone RS232 console management via CH01M